Methods and Precautions for Operating Precision Surface Grinding Machines


Release time:

2021-08-05

Before 1. operation 1. Employees who operate precision surface grinders before operation must wear protective masks, aprons and other protective equipment, fasten their clothes, and fasten their cuffs. It is strictly forbidden to wear gloves for operation; 2. Strictly carry out equipment spot check according to the spot check system and make corresponding records; Before working, add oil and water according to the use regulations of precision surface grinder, and check whether the oil mark, water mark, oil quantity and water quantity are normal. Check whether the oil circuit and circuit are unblocked; keep the lubrication system clean, and the oil tank and water tank shall not be open; 3. Check whether each handle is in the specified position, whether the operation is flexible, and whether the safety protection device is intact and complete. Each connected component is

Before 1. operation

1. Employees who operate precision surface grinders before operation must wear protective masks, aprons and other protective equipment, fasten their clothes, and fasten their cuffs. It is strictly forbidden to wear gloves for operation;

2. Strictly carry out equipment spot check according to the spot check system and make corresponding records; Before working, add oil and water according to the use regulations of precision surface grinder, and check whether the oil mark, water mark, oil quantity and water quantity are normal. Check whether the oil circuit and circuit are unblocked; keep the lubrication system clean, and the oil tank and water tank shall not be open;

3. Check whether each handle is in the specified position, whether the operation is flexible, and whether the safety protection device is intact and complete. Whether the connecting parts are fastened and the brake is complete and flexible;

4. Before placing the workpiece, open the grinding wheel cover and turn the grinding wheel by hand to check the tightness, integrity and balance of the grinding wheel. Grinding wheels of different materials should be used for different materials. If the machine is shut down for more than 8 hours, it should be idle for 3-5 minutes to make the system run normally before use;

5. The operator should be familiar with the general performance and structure of the precision surface grinder, the transmission system, and the use of super performance is strictly prohibited.

In 2. operation

1. Turn on the main power switch, turn on the magnetic absorption switch, press the start button of the oil pump and grinding wheel, run the empty car, and confirm that all parts of the precision surface grinder work normally and correctly before formal operation;

2. Before the workbench moves. Ensure that the installed workpiece should be neat and firm. It is forbidden to correct the grinding wheel or hammer on the machine tool worktable. It is forbidden to put anything on the control table to avoid damaging the precision surface grinding machine and affecting the processing accuracy;

3. When starting, start the magnetic absorption, oil pump, grinding wheel, water pump and travel switch in turn. When the next knife, strictly control the distance of the next knife to avoid too much damage to the grinding wheel and workpiece. Generally speaking, for the modified magnetic core, resin adhesive type grinding wheel is usually selected, and the feed amount for each time shall not exceed 0.2mm. The first feed and the last feed shall be controlled within O.1 mm. For the magnetic core with direct air gap, metal adhesive grinding wheel is usually used, and the feed amount for each time shall not exceed 0.1mm, and the feed amount for the first feed and the last feed shall be controlled within 0.05mm;

4. The length and width of the workpiece is strictly prohibited beyond the length and width of the table top;

5. In the grinding process, the grinding wheel is not allowed to stop when the grinding wheel does not exit the workpiece on the working surface. When parking, the grinding groove should be stopped first, and then the water pump should be stopped in turn. After the grinding wheel, oil pump and demagnetization, the grinding workpiece can be removed;

6. The positioning safety device must be used when automatically walking the knife. The position of the handle shall be fixed when moving fast. No one or anything is allowed to approach within the operating range of the workbench. Pay attention to the movement of the workbench to prevent collision accidents;

7. For each polished workpiece, sampling inspection should be carried out (for the magnetic core, the sampling ratio is 3%, the other depends on the specifications of the workpiece), and the workpiece can be removed only after the sampling results fully meet the process requirements;

8. When loading and unloading the grinding wheel, cut off the power supply and pad the wooden plate on the work surface. Before loading the grinding wheel, it must be ensured that the grinding wheel has been balanced. Regularly use special tools (diamond corrector or workpiece) and level to trim the grinding wheel and correct the balance of the working surface, generally once a week, if the machine tool is abnormal. Such as after grinding the workpiece deformation or consistency is not good. The grinding wheel shall be corrected immediately and the work surface shall be corrected;

9. During the operation of the precision surface grinder, if there is any abnormal situation, the operation should be stopped immediately, the power supply of the equipment should be turned off, and the professional maintenance personnel should be notified for maintenance;

10. Work should be concentrated, not to do things unrelated to work.