Surface Grinder Manufacturers Explain the Whole Grinding Process of Surface Grinder


Release time:

2023-03-10

The surface grinder manufacturer explained the whole grinding process of the surface grinder. The surface grinder is composed of many parts. During the production process, the movement direction of the grinding rod is consistent with the movement direction of the sand wheel shaft. Only in this way can the self-priming oil discharge quickly generate the oil wedge according to the radial clearance during work, thus improving the operation characteristics and being beneficial to the production error.

  Surface grinding machine manufacturersExplain the surface grinding machine in the grinding process

The surface grinder of the surface grinder manufacturer is composed of many components. During the production process, the movement direction of the grinding rod is consistent with the movement direction of the sand wheel shaft during operation. Only in this way can the self-priming oil discharge quickly generate an oil wedge according to the radial clearance during operation, thus improving the operation characteristics and being beneficial to the endless errors in production.

The surface grinder of the surface grinder manufacturer pays special attention to the following four points in the grinding process:

1. In the grinding process, the front and rear rolling bearings need to be continuously adjusted (to maintain a certain touch) to improve the grinding efficiency and ensure the geometric accuracy of the bearings;

2. Eliminate the excess grinding fluid at the top of the rolling bearing anytime and anywhere to prevent the bell mouth period of the front and rear rolling bearings;

3. When grinding, the grinding liquid should avoid and appropriately tighten the front and rear rolling bearings to ensure the accuracy of the front and rear bearings;

4. Draw out the grinding rod after grinding for a certain period of time, eliminate the grinding fluid in the grinding rod and the front and rear rolling bearings, and check the grinding performance and the grinding condition of the grinding rod. If the grinding rod is damaged, it needs to be repaired to ensure the consistency of the diameter of the front and rear rolling bearings.

e1d00e98-a79a-4cfb-82f3-c640a07b4b93.jpg

Surface grinding machine manufacturers

All machinery and equipment in the production process are the need to pay attention to the problem of things, so is the surface grinder. Only in the grinding production process with a surface grinder, pay attention to the above four points, in order to make the surface grinder production level appears, and then produce products that meet the requirements.

  Surface grinding machine manufacturersHow to solve the vibration problem after the production of plane grinding machine surface equipment

First, it is the living environment of production and processing. There is no way to place high-precision surface grinders around the same working environment. For example, high-speed punching machines, CNC lathes and other CNC lathes with relatively large vibration can easily cause co-seismic. How can we judge whether there is co-seismic? Stop using the grinder and start the high-speed punching machine or CNC lathe. If the hand touches the grinder, the feeling of vibration or hemp hand is affected. Therefore, we must separate the production workshop.

Second, check the road surface. If the anchor bolt level of the CNC lathe is not adjusted properly, it will cause the co-vibration of the CNC lathe. Because sometimes the ground flatness of the production and processing site is not very good, it is necessary to adjust the horizontal screw to make the CNC lathe reach a flat relative height. According to tighten the anchor bolts, let each anchor bolt stick to the site.

Third, if the vibration is not removed after the above posture is completed, it should be checked whether it is caused by the wood floor on the road surface being too depressed. If the road surface is terrazzo floor or the paved floor plate is relatively firm, if it is cement flat, the road surface will also cause co-earthquake. How to deal with this situation? Can go to the plastic hardware store to buy a few pieces of gray-black rubber pads, thin 6-10mm up and down, size 10cm and the size of the seat cushion slightly larger, loose the anchor bolts, the rubber pad pad under the standard seat cushion, can play a very large shock absorption effect.

Fourth, if the vibration is not cleared, you can try it with a sand wheel. If the flange plate is installed with the counterweight without the effective counterweight calibration, then remove the counterweight and install it. If it is really not possible, try it with a new flange, and the general problem can be solved.

If you need a surface grinder, you can contact us.Surface grinding machine manufacturers.