Some knowledge points of CNC grinding machine, CNC forming grinding machine manufacturers tell you


Release time:

2022-05-16

CNC molding grinder manufacturers believe that the fault parts of CNC grinding machine are mainly CNC system and machine tool body. Because the numerical control system is limited by the objective conditions, the working conditions of the bearing numerical control grinding machine are quite bad, the numerical control system is prone to soft and hard faults, and it is difficult to find the fault point, and the maintenance is quite difficult.

CNC forming grinderManufacturers believe that the fault parts of CNC grinding machine is mainly CNC system and machine tool body. Because the numerical control system is limited by the objective conditions, the working conditions of the bearing numerical control grinding machine are quite bad, the numerical control system is prone to soft and hard faults, and it is difficult to find the fault point, and the maintenance is quite difficult. Because the domestic CNC grinding machine manufacturers want to reduce costs as much as possible, so the selection of supporting parts are also made in China. For example, the ball screw and roller guide of the transmission part are of poor quality and short service life. Due to the influence of its materials and heat treatment, the transmission accuracy of the CNC grinder generally decreases after one year of operation, resulting in poor positioning accuracy of the machine tool and poor repeated positioning accuracy.

CNC forming grinderManufacturers believe that the characteristics of CNC bearing grinder:

1. High precision. CNC molding grinder manufacturers believe that in order to ensure the accuracy of bearing grinding, in addition to the geometric accuracy and good structural characteristics of the machine body, it can also be achieved by reducing the error of the CNC system and using certain compensation technology. At the same time, it must have high-precision position measurement and high-performance numerical control system with pulse equivalent of 0.1m m.

2. High-speed and efficient processing. Increasing productivity is also the main feature of CNC machine tools. Therefore, the speed of the frequency conversion spindle is generally 60000 r/m in. When the processing diameter is less than 20mm, the spindle speed of 75000 r/min can also be selected. The CNC system automatically distributes the feed speed and feed rate of the four stages of fast walking, rough grinding, fine grinding and light grinding according to the machining allowance, which will be automatically eliminated.

3. High reliability is the key indicator of CNC machine tools. CNC molding grinder manufacturers believe that if the average trouble-free working time to assess, the average need to ensure more than 40000 hours.

4. Intelligent use of adaptive control technology to detect the signal of spindle current changes in the process of bearing grinding, automatic adjustment of CNC system feed speed, feed speed and other grinding parameters, improve the grinding state, to achieve good grinding effect. At the same time, the numerical control system should have a self-diagnosis function, which can find and eliminate the fault parts in time.

CNC forming grinderManufacturers believe that the type of CNC bearing grinder and the scope of application:

1. Open-loop servo system. The manufacturer of the numerical control forming grinder believes that when the boring grinder 3MZ144 grinds the groove of the ordinary bearing, there is no position measurement, and the input data is distributed by the operation of the numerical control system to output command pulses to control the operation of the stepping motor, and the command is issued without feedback. This control method is only applicable to the processing of ordinary precision products. The bearing engineer union is very good! (Bearing House WeChat pay close attention)

2. Closed-loop servo system. The manufacturer of the numerical control forming grinder believes that when the boring grinder 3 M K205D grinds the aperture, the tolerance range of the inner diameter control dimension of the bearing P4 is within 0-4m, and is equipped with an automatic detection device. During the grinding process, the signal will be fed back to the CNC system at any time according to the change of the ferrule processing size. This control method is suitable for processing high-precision products.

3. Semi-closed loop servo system. CNC forming grinder manufacturers believe that such as groove grinder 3MK135D3MK147D, can process grooves, control the size of the tolerance range is wide, within 0-30 m, because the worktable is not fully incorporated into the control loop, can not compensate the screw and guide rail transmission error. This control method is suitable for products with small dimensional tolerances.