Operating Procedures for CNC Grinding Machines


Release time:

2021-08-17

CNC grinding machine is a machine tool that uses grinding tools to grind the surface of the workpiece through numerical control technology. Most of the grinding machine is the use of high-speed rotating grinding wheel for grinding, a few is the use of oilstone, abrasive belt and other abrasive and free abrasive processing, such as honing machine, super finishing machine, abrasive belt grinding machine, grinding machine and polishing machine. CNC grinding machine also has CNC surface grinding machine, CNC centerless grinding machine, CNC inside and outside grinding machine, CNC vertical universal grinding machine, CNC coordinate grinding machine, CNC forming grinding machine and so on.

CNC grinding machine is a machine tool that uses grinding tools to grind the surface of the workpiece through numerical control technology. Most of the grinding machine is the use of high-speed rotating grinding wheel for grinding, a few is the use of oilstone, abrasive belt and other abrasive and free abrasive processing, such as honing machine, super finishing machine, abrasive belt grinding machine, grinding machine and polishing machine. CNC grinding machine also has CNC surface grinding machine, CNC centerless grinding machine, CNC inside and outside grinding machine, CNC vertical universal grinding machine, CNC coordinate grinding machine, CNC forming grinding machine and so on.

cnc grinding machine operating procedures:

1. The operator is allowed to operate only after passing the examination and obtaining the operation certificate. The operator should be familiar with the performance and structure of the machine and abide by the safety and shift system.

2. The operator must understand and memorize the lubrication parts, lubrication methods and the type and brand of lubricating oil in detail according to the requirements of the manual of the numerical control grinding machine, and carry out oil supply maintenance according to the lubrication chart of the grinding machine.

3. Before starting work, protective articles shall be worn according to regulations, and all parts of the CNC grinder shall be inspected in detail according to the shift change record book. Any problems found shall be reported step by step in a timely manner. No driving shall be allowed without exclusion of abnormal conditions.

4. The following parts of the CNC grinder shall be inspected before commencement:

(1) Whether the amount of oil in the oil pool of the grinding wheel carrier reaches the specified oil level.

(2) adjust the belt tightness is appropriate.

(3) whether the reciprocating motion of the shaking hand wheel, worktable and grinding wheel frame is good.

(4) The protective cover of the grinding wheel and the grinding wheel shall be firmly installed, the position shall be correct, and the dust shield felt of the guide rail of the workbench shall be in close contact.

(5) Check whether the electrical system (motor, distribution box, safety light, wire, ground wire) is in good condition, and whether the surrounding environment is clean and free from short circuit.

(6) Check all lubrication parts, sliding surfaces and transmission system, and inject lubricating oil.

(7) Turn on the power supply, start the motors of the oil pump, grinding wheel frame and headframe in sequence, and pay attention to the running state. If abnormal sound is found, the power shall be turned off immediately, and the vehicle shall be started after inspection and treatment.

(8) start the grinder, idling for 2~3min, check whether the action of each part is normal. If there are abnormal conditions such as mechanism failure, bearing overheating, insufficient oil pressure, grinding wheel swing, unstable workbench movement, etc., stop the power supply and take measures to deal with it. Users are strictly prohibited from disassembling and handling by themselves beyond the scope of self-inspection and self-repair.

(9) Check whether the motor of the cooling pump is running normally and whether the cooling liquid is unblocked.

(10) When loading the grinding wheel, a paper pad of 0.5~1.0mm should be placed between the grinding wheel and the pressing plate. A special wrench must be used to tighten it evenly. It is not allowed to tighten it with lengthened pipes to avoid bursting the grinding wheel.

(11) After the grinding wheel is installed, it should run for 5min without load. The operator should avoid the front and confirm that the grinding wheel is running normally before it can be used.

5. The clamping of the workpiece must conform to the regulations. For the workpiece interrupted for some reason, it must be confirmed that it is in good condition before starting work.

6. When processing the workpiece, the grease, black dirt and dust on the workpiece must be removed in advance. According to the material of the workpiece, the grinding wheel and the grinding amount are reasonably selected, and it is strictly prohibited to grind the blank of the workpiece.

7. When loading and measuring the workpiece, the grinding wheel must be withdrawn from the workpiece and stopped. When the workpiece and grinding wheel do not leave, stop the vehicle midway. When the grinding wheel is close to the workpiece, it is not allowed to be motorized.

8. When working, it is forbidden for the operator to leave the CNC grinder or entrust the escrow. If it is necessary to leave due to power failure or other reasons, the grinding wheel should be stopped after leaving the workpiece. When the grinder is started again, it shall be confirmed that all parts are not abnormal before driving.